Ground waterproofing method ground waterproofing material

Ground waterproofing is an important part of home decoration. A slight carelessness will bring unnecessary troubles, especially in the kitchen and bathroom space. The maximum amount of water used is that the indoor humidity is high. Waterproofing must be done before the tile is applied, otherwise it will be Seriously affect the quality of home renovation projects. Then, Xiaobian will introduce the ground waterproofing method and ground waterproof material for everyone.

Ground waterproofing method

The seams between the wall and the ground and the pipe seams between the upper and lower water are the most prone to problems. The corners must be properly handled. The decoration team is required to provide cement mulch to the upper and lower water pipes in the kitchen and bathroom. Brush a 10 to 20 cm polyurethane waterproof coating upward from the floor, and then re-do the polyurethane waterproofing on the ground, and add the original waterproof layer to form a composite waterproof layer. To enhance waterproofness. There will be a transfer excuse for the water pipes at the transition between the wall and the ground. It must be ensured that there will be no water leakage at the interface. After the installation is complete, the water test can be conducted.

Ground waterproofing method II

When the bathroom takes a bath, the water will splash on the adjacent wall. If there is no protection of the waterproof layer, the partition wall and the diagonal corner wall will become mildly damp. So be sure to waterproof the walls before you apply the wall tiles. In the general waterproofing process, the wall surface is to be treated with a waterproof height of 30 cm. However, for a non-load-bearing lightweight wall, the entire wall should be waterproofed, and at least 1.8 meters high should be achieved. The waterproof surface of the wall adjacent to the shower position should also be 1.8 meters high. If a bathtub is used, the height of the waterproof coating on the wall adjacent to the bathtub is also higher than the upper edge of the bathtub.

Ground waterproof method three

Be sure to level the floor first with cement mortar and then do a waterproof treatment so that leakage of the waterproof coating due to uneven thickness can be avoided. The specific approach is, before doing waterproofing, be sure to clean the ground, with polyurethane waterproof coating repeated brushing 2 to 3 times. , And try to ensure the formation of a smooth, do not have large air bubbles in the process of laying the gap.

Ground waterproofing method four

During the construction process, when the pipeline, floor drain, etc. cross the floor, the waterproof layer around the hole must be seriously constructed. Buried water pipes in the wall, so that a reasonable layout, decoration design, the laying of the water pipes must be neat and unified, do not mess scattered. Laying pipes shall be made of grooves larger than the diameter of the pipes. The grooves shall be smooth and smooth, and then the grooves shall be brushed with polyurethane waterproof coating.

Floor waterproof material

1, asphalt waterproof material. The natural asphalt, petroleum asphalt and coal asphalt as the main raw materials, made of asphalt linoleum, asphalt tire felt, solvent-based and water emulsion bitumen or asphalt rubber coatings, ointments, with good adhesion, plasticity, Water resistance, corrosion resistance and durability.

2, rubber plastic waterproof material. With neoprene rubber, butyl rubber, ethylene propylene diene monomer, polyvinyl chloride, polyisobutylene and polyurethane as raw materials, it can be made into elastic tireless waterproof membrane, waterproof film, waterproof coating, coating material and ointment, cement Sealing materials, such as sealing tapes, have high tensile strength, high elasticity and elongation, good adhesion, water resistance, and weather resistance. They can be used coldly and have a long service life.

3, cement waterproof material. Admixtures with a coagulative effect on cement, such as water repellents, air entrainers, and expansive agents, can increase the hydrophobicity and impermeability of cement mortars and concrete; and promote coagulation with cement and sodium silicate as base materials. Mortar, can be used for underground engineering plugging and waterproofing.

4, metal waterproof material. Thin steel plate, galvanized steel plate, profiled steel plate, coated steel plate, etc. can be directly used as roofing panels for waterproofing. Thin steel plates are used for metal waterproofing of basements or underground structures. Thin copper plates, thin aluminum plates, and stainless steel plates can be used as waterproofing strips for building deformation joints. The connection of the metal waterproof layer is to be welded and painted with a rust-proof protective paint.

Editor's summary: The ground waterproofing method and ground waterproof material are introduced here, and we hope to be helpful to everyone. If you want to know more related information, you can pay attention to this website information.

Decoration waterproof